SIL-4H1: Commercial-Grade SDI-12 Digital Output Horizontal/Vertical Field of View Infrared Radiometer Sensor

$465.00

The SIL-4H1 has an SDI-12 digital output and high-quality cable terminating in pre-tinned pigtail leads for easy connection to dataloggers and controllers. The unique geometry of the sensor gives a wide 32° half-angle field of view in the horizontal/horizontal direction with a 13° half-angle field of view in the vertical/horizontal direction. This enables the user to mount the sensor at shallower angles without seeing above the horizon while maximizing the area measured. The sensor has a response time of 0.1 seconds. The SIL-4H1 is designed to be mounted with an Apogee AM-250 commercial-grade mounting bracket.

Typical applications include plant canopy temperature measurement for use in plant water status estimation, road surface temperature measurement of determination of icing conditions, and terrestrial surface (soil, vegetation, water, snow) temperature measurement in energy balance studies. 

The IR sensor can be removed from the shield and rotated to either a vertical or horizonal orientation.

FOR MORE PRODUCT INFORMATION, CHECK OUT THESE LINKS

• Product Manual

• Specification Sheet

• Technical Drawing

 

RESEARCH-GRADE VS COMMERCIAL-GRADE

 Research-GradeCommercial-Grade
Accuracy ± 0.2 C from -30 to 65 C ± 0.5 C from 0 to 50 C
Shield Material Powder-coated aluminum with a polished interior Rugged, polished, UV-resistant ASA plastic
Field of View Three circular with two horizontal apertures One circular and one horizontal aperture
Cost More accurate with higher cost Less accurate with lower cost
Cable Connector IP68 stainless-steel cable connector to simplify sensor removal No connector

MORE INFORMATION ON APOGEE INFRARED RADIOMETERS >> click here

Full Description
Where to Buy

The SIL-4H1 has an SDI-12 digital output and high-quality cable terminating in pre-tinned pigtail leads for easy connection to dataloggers and controllers. The unique geometry of the sensor gives a wide 32° half-angle field of view in the horizontal/horizontal direction with a 13° half-angle field of view in the vertical/horizontal direction. This enables the user to mount the sensor at shallower angles without seeing above the horizon while maximizing the area measured. The sensor has a response time of 0.1 seconds. The SIL-4H1 is designed to be mounted with an Apogee AM-250 commercial-grade mounting bracket.

Typical applications include plant canopy temperature measurement for use in plant water status estimation, road surface temperature measurement of determination of icing conditions, and terrestrial surface (soil, vegetation, water, snow) temperature measurement in energy balance studies. 

The IR sensor can be removed from the shield and rotated to either a vertical or horizonal orientation.

FOR MORE PRODUCT INFORMATION, CHECK OUT THESE LINKS

• Product Manual

• Specification Sheet

• Technical Drawing

 

RESEARCH-GRADE VS COMMERCIAL-GRADE

 Research-GradeCommercial-Grade
Accuracy ± 0.2 C from -30 to 65 C ± 0.5 C from 0 to 50 C
Shield Material Powder-coated aluminum with a polished interior Rugged, polished, UV-resistant ASA plastic
Field of View Three circular with two horizontal apertures One circular and one horizontal aperture
Cost More accurate with higher cost Less accurate with lower cost
Cable Connector IP68 stainless-steel cable connector to simplify sensor removal No connector

MORE INFORMATION ON APOGEE INFRARED RADIOMETERS >> click here

Current Stock:
Input Voltage Requirements 5.5 to 24 V DC Current Draw 1.5 mA (quiescent); 2.0 mA (active) Calibration Uncertainty (0 to 50 C), when target & detector ΔT are < 20 C 0.5 C Measurement Repeatability Less than 0.05 C Long-term Drift Less than 2 % change in slope per year when germanium filter is maintained in a clean condition Response Time 0.6 s, time for detector signal to reach 95 % following a step change Field of View (half-angle) 32° horizontal; 13° vertical Spectral Range 8 to 14 µm; atmospheric window Operating Environment -50 to 80 C; 0 to 100 % relative humidity (non-condensing) Dimensions 23 mm diameter, 60 mm length Mass 190 g Warranty 4 years against defects in materials and workmanship Manufactured Assembled in the USA